3 Layouts to share!

Hello!

You are with Sandrine today! I would like to share my first 3 layouts for Green Tara!

I will start with a girlie layout.

"Darling Daughter"

In this first layout I used loads of different flowers, "8 cm Lavender Damask flower", "8 cm Lavender Velvet Rose", "Violet Cherry Blossoms" and "White Flower Spray", "White Pearl Lace Flower: and "2.5cm Metal Heart" all with a coat of Gesso.

 Some "Opal Velvet Glitter Ribbon" behind the photo and another "Damask Flower".

I added some details to the edge using torn "White Mesh".

More "Glitter Ribbon", a "Cherry Blossom" and "Skeletal Mesh".

GREEN TARA PRODUCTS USED:

- DAMASK 8CM FABRIC AND ORGANZAFLOWER LAVENDER XF9225Lav 

- VELVET ROSE 8CM VELVET FLOWER LAVENDER XF9217L

- 100MM SKELETON MESH SILVER RB175SG

- 25MM VELVET GLITTER RIBBON OPALRB324Op25 

- CHERRY BLOSSOM VIOLET FLC22V 

- 37MM MESH WHITE RB6734WH 

- FLOWER SPRAYS WHITE PFST1100 

- LACE PEARL 3.5CM WHITE XF9332Wh 

- METAL EMBELLISHMENT HEART 2.5CMMESH

Here is my second project:

"Family Snap" 

A close up of the flower cluster: All my flowers were covered with some Gesso, "3.5cm Lace Pearl", "8cm Damask Flower", "6.5cm Heirloom Silk and Organza Flowers", "1.5cm roses" all in Ivory:

Here I used some ribbon: a little tip on how to adhere sheer organza ribbon discreetly, I first used double sided tape where I knew it was going to be covered and attached the edges with a couple of stitches, I used

"Ivory Satin Hearts Ribbon" and "Vertical Stripe Satin Ribbon".

 

A "1.5cm rose".

GREEN TARA PRODUCTS USED:
- 3.5CM LACE PEARL FLOWER XF9332Iv 
- DAMASK 8CM FABRIC AND ORGANZAFLOWER IVORY XF9225Iv 
 - HEIRLOOM 6.5CM SILK AND ORGANZAFLOWER IVORY XF9213Iv 
- 1.5CM ROSE WHITE FDR0003Wh 
- 18MM DOUBLE SIDED VERTICAL STRIPESATIN IVORY RB545Iv 
- ORGANZA SATIN  HEARTS RIBBON IVORY RB255Iv

My third project was created for Scrapping Outback's November Xmas Challenge:

"Merry Christmas 2012"

I went for a neutral colour combo,  I used some "Skeleton Ribbon" at the bottom of my photo matting

 (it is one of my favourite Green Tara products!!!!).

I made my own "wreath" photo frame by wrapping gorgeous "Jute Ribbon" around a wire circle, I simply stitched it together at the end:

Also more gold in the cluster at the top using "Natural Jute Ribbon" & "Gold Leaf Garland":

I altered a "Silver Leaf" with gesso and distress stickles and wrapped it around my photo frame, added a gorgeous gold leaf garland and some "Skeleton Mesh in gold":

A wooden reel with some "Gold mesh", another little tip, try using ribbon and trims in a different manner every time you use them.

Green Tara Products used:

- 100MM SKELETON MESH GOLD RB17GO

- CHERRY BLOSSOM WHITE FLC22WH

- WHITE APPLE BLOSSOM FDV044WH

- 15MM NATURAL JUTE RIBBON RB17Nat15

- CAMELLIA 8CM PAPER FLOWER IVORY XF9219IV

- SILVER LEAF 3CM XL2665P

- SATIN LEAF GARLAND GOLD RB573AG

- 38MM MESH GOLD RB6734GO

Well that's it for me today, I hope you enjoyed my first post! 

Until next time, Happy Scrapping!